Abstract
The microstructural evolution during processing and tensile deformation of a nanocrystalline Al-Ti-Cu alloy was investigated using transmission and scanning electron microscopy. Grain refinement was achieved by cryomilling of elemental powders, and powders were consolidated by hot isostatic pressing (“HIPing”) followed by extrusion to produce bulk nanocrystalline Al-Ti-Cu alloys. In an effort to enhance ductility and toughness of nanocrystalline metals, multiscale structures were produced that consisted of nanocrystalline grains and elongated coarse-grain (CG) bands of pure aluminum. Examination of bulk tensile fracture samples revealed unusual failure mechanisms and interactions between the CG bands and nanocrystalline regions. The ductile CG bands underwent extensive plastic deformation prior to fracture, while nanocrystalline regions exhibited nucleation and growth of voids and microcracks. Cracks tended to propagate from nanocrystalline regions to the CG bands, where they were effectively arrested by a combination of crack blunting and crack bridging. These processes were instrumental in enhancing the toughness and ductility of the nanocrystalline alloy.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
M.C. Roco, R.S. Williams, and P. Alivisatos: Nanotechnology Research Directions, Kluwer Academic Publishers, Dordrecht, Netherlands, 2000, ch. 7.
D. Bloor, R. Brook, M. Flemings, and S. Mahajan: The Encyclopedia of Advanced Materials, Elsevier Science Inc., New York, NY, 1994, vol. 3, pp. 1719–34.
R.W. Siegel: in Processing and Properties of Nanocrystalline Materials, C. Suryanarayana, J. Singh, and F.H. Froes, eds., TMS, Warrendale, PA, 1996, pp. 3–10.
J.E. Carsley, A. Fisher, W.W. Milligan, and E.C. Aifantis: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 2261–71.
X.K. Sun, H.T. Cong, M. Sun, and M.C. Yang: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 1017–24.
R.W. Hayes, R. Rodriguez, and E.J. Lavernia: Acta Mater., 2001, vol. 49, pp. 4055–68.
Z. Lee, R. Rodriguez, E.J. Lavernia, and S.R. Nutt: in Ultrafine Grained Materials II, Y.T. Zhu, T.G. Langdon, R.S. Mishra, S.L. Semiatin, M.J. Saran, and T.C. Lowe, eds., TMS, Warrendale, PA, 2002, pp. 653–59.
S.L. Semiatin, K.V. Jata, M.D. Uchic, P.B. Berbon, D.E. Matejczyk, and C.C. Bampton: Scripta Mater., 2001, vol. 44, pp. 395–400.
J. Benedict, R. Anderson, and S.J. Klepeis: Mater. Res. Soc. Symp. Proc., 1992, vol. 254, pp. 121–40.
T.R. Malow and C.C. Koch: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 2285–95.
T.R. Malow and C.C. Koch: Acta Mater., 1998, vol. 46, pp. 6459–73.
F. Zhou: Univ. of California at Irvine, Irvine, CA, unpublished research, 2001.
R. Rodriguez, R.W. Hayes, P.B. Berbon, and E.J. Lavernia: Acta Mater., 2003, vol. 51, pp. 911–29.
J. Rosler, R. Joos, and E. Arzt: Metall. Trans. A, 1992, vol. 23A, pp. 1521–39.
E.A. Brandes: Smithell’s Metals Reference Book, 7th ed., Butterworth Heinemann, London, 1992, ch. 22.
R.Z. Valiev, Y.V. Ivanisenko, E.F. Rauch, and B. Baudelet: Acta Mater., 1996, vol. 44, pp. 4705–12.
A.A. Nazarov, A.E. Romanov, and R.Z. Valiev: Acta Metall. Mater., 1993, vol. 41, pp. 1033–40.
L. Dupuy and J.-J. Blandin: Acta Mater., 2002, vol. 50, pp. 3251–64.
M. Jain, and T. Christman: Acta Metall., 1994, vol. 42, pp. 1901–1911.
J.E. Carsley, A. Fisher, W.W. Milligan, and E.C. Aifantis: Metall Mater. Trans. A 1998, vol.29A, pp. 2261–71.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Lee, Z., Nutt, S.R., Rodriguez, R. et al. Microstructural evolution and deformation of cryomilled nanocrystalline Al-Ti-Cu Alloy. Metall Mater Trans A 34, 1473–1481 (2003). https://doi.org/10.1007/s11661-003-0259-x
Received:
Issue Date:
DOI: https://doi.org/10.1007/s11661-003-0259-x